MASTERCRAFTPREMIUM ELECTRIC CHAIN SAWOWNER’S MANUALIMPORTANTRead and understand this manual before assembling or operating this chain saw.Improper use
10100549SAW CHAIN TENSIONADJUSTMENTNote: For pre assembled models, the saw chain tension isproperly set at factory. A new chain will stretch. Check ne
1111100549Figure 16 - Assembling Guide Bar, Chain, and Hand GuardAdjustingBlockAdjustingScrewSprocketSupportAdjustingPlateFigure 17 - Part Locations f
12100549CLEANING SAW BODYKeep saw body clean. Use a soft cloth dampened with a mildsoap and water mixture. Wipe saw body to clean.CARE OF GUIDE BARUne
1313100549CLEANING AND MAINTENANCEContinuedSharpening CuttersUse file guide for 30° filing.1. Adjust chain for proper tension (see Saw Chain TensionAdju
14100549CLEANING AND MAINTENANCEContinuedSTORAGEIf storing saw for more than 30 days, follow steps below.1. Drain oil tank.2. Remove and clean guide b
1515100549TROUBLESHOOTINGOBSERVED FAULTSaw runs, but does not cut.Saw does not cut unless heavily forced.Cutting produces only sawdust with fewlarge c
100549-01REV. B7/93WARRANTY INFORMATIONKEEP THIS WARRANTYAlways specify model and serial numbers when writing.We reserve the right to amend these spec
TRONÇONNEUSE ÉLECTRIQUE PRIMEMANUEL D’UTILISATION ET D’ENTRETIENLa classification ACNOR (CSA) de cette tronçonneuse est 2C; tronçonneuse conçue pour l
2100549DESCRIPTION SYMBOLES!WARNING ICON G 001Lire le manuel d’instructions.Ne pas exposer à la pluie ni utiliser en conditionshumides.Si le cordon es
33100549!WARNING ICON G 001AVERTISSEMENTSPOUR LA SÉCURITÉLire et comprendre tous les avertissements pourla sécurité qui figurent aux pages 3 et 4.L’ut
2100549INFORMATION SYMBOLS!WARNING ICON G 001Read Instruction ManualDo Not Expose to Rain or Use in Wet ConditionsRemove Plug Immediately if Cable is
4100549Ne pas laisser lenez de la lame-guide toucherici.Figure 1 - Exemple du risque de recul. Ne pas laisser lenez de la lame-guide toucher un objet
55100549!WARNING ICON G 001AVERTISSEMENTSPOUR LA SÉCURITÉSuite5. N’abattre un arbre que si l’on a été formé ou si l’on disposed’assistance expérimenté
6100549NOMENCLATURE DES PIÈCESCordon électriquePoignéearrièreLame-guideRegard du niveau d’huile (situé surle carter de la tronçonneuse, cachépar la po
77100549À suivreDÉBALLAGE1. Sortir du carton toutes les pièces.2. Vérifier toutes les pièces pour déceler d’éventuels dégâtsdurant l’expédition. Si l’
8100549UTILISATION DE LA TRONÇONNEUSESuite3ème entaille - entaille par ledessous du reste de la branchepour éviter les éclats5 à 10 cm1ère entaille -
99100549UTILISATION DE LATRONÇONNEUSESuiteABATTAGE D’UN ARBRE!WARNING ICON G 001AVERTISSEMENT•Éviter la réaction de recul qui peut provoquerdes blessu
10100549UTILISATION DE LATRONÇONNEUSESuite!WARNING ICON G 001AVERTISSEMENTNe pas scier l’arbre complètement. Laisserenviron 5 cm (2 po) de bois non sc
1111100549La bille est soutenue à une extrémité.1. Faire la première entaille sur le dessous de la bille. (Voir lafigure 12.) Pour ce faire, utiliser
12100549RÉGLAGE DE LA TENSIONDE LA CHAÎNEFigure 14 - Pour tourner la vis de réglage!WARNING ICON G 001AVERTISSEMENTAvant de régler la tension de la ch
1313100549Figure 16 - Assemblage de la lame-guide, de la chaîne etde l’écran de protection de la mainVis deréglageSupport depignonPlaque deréglageFigu
33100549!WARNING ICON G 001SAFETY WARNINGSThis saw has a chain brake. When kickback occurs, the fronthand guard is moved forward by the back of operat
14100549NETTOYAGE ET ENTRETIENAVISLes instructions pour l’entretien de latronçonneuse se trouvent ci-dessous. Toutentretien qui n’est pas mentionné ci
1515100549NETTOYAGE ET ENTRETIENSuiteFILE HOLDERGuide limeLime ronde de 4mm (5/32 po)Directiondu limageFigur
16100549Figure 22 - Position de l’outil pour limiteurde profondeur sur la chaîneNETTOYAGE ET ENTRETIENSuiteLimage des limiteurs de profondeur des tail
1717100549DÉPANNAGE!WARNING ICON G 001AVERTISSEMENTAvant de faire l’entretien, débrancher la tronçonneuse de la prise de courant.Des blessures graves
18100549NOTES_________________________________________________________________________________________________________________________________________
1919100549NOTES_______________________________________________________________________________________________________________________________________
100549-01REV. B7/93INFORMATION SUR LA GARANTIECONSERVER CETTE GARANTIEDans toute correspondance, toujours préciser les numéros de modèle et de série.N
4100549!WARNING ICON G 001SAFETY WARNINGSContinued7. Secure wood you are cutting by using clamps or chocks.8. Grip chain saw firmly with both hands. Ne
55100549PRODUCT IDENTIFICATIONLimbing Process of cutting limb(s) from a felled tree.Low-Kickback Chain Chain that reduces chance ofkickback as requi
6100549EXTENSION CORDSUse proper extension cord with this chain saw. Use onlyextension cords marked for outdoor use. Use an extension cordno less than
77100549OPERATING CHAIN SAWContinuedTRIMMING A TREE (Pruning)Trimming a tree is the process of cutting limbs from a livingtree. Make sure your footing
8100549OPERATING CHAIN SAWContinuedFigure 10 - Limbing A TreeLimbing is removing branches from a fallen tree. Make sureyour footing is firm. Keep feet
99100549OPERATING CHAIN SAWContinued2nd Cut1st CutFigure 12 - Bucking Log When Log Is SupportedOn One End1st Cut2nd CutFigure 13 - Bucking Log When Lo
Commentaires sur ces manuels